ASTM D Determining Ignition Temperature of Plastics. This standard test method tests the flash ignition temperature and spontaneous ignition. ASTM D Test Report. |. Page 2. ASTM D Test Report. |. Page 3. ASTM D Test Report. |. Page 4. ASTM D Test Report. |. Page 5. For this reason, the “Standard Test Method for Determining Ignition Temperature of Plastics” — referred to as ASTM D — was developed. This test.
|Published (Last):||3 May 2017|
|PDF File Size:||19.42 Mb|
|ePub File Size:||2.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
For plastics in sheet form, sheets of 20 astk x 20 millimeters are required to be stacked atop one another until a total mass of three grams is attained. Work Item s – proposed revisions of this standard.
ASTM D – 16 Standard Test Method for Determining Ignition Temperature of Plastics
Certification Formally confirming that your products and asym meet all trusted d19929 and internal standards. Decompose and release the combustible gas from plastic material under regulated testing conditions,ignited by outer flame and burned a certain time,to measure the minimum temperature of the material.
Per ASTM D, “This standard is used to measure and describe the response of materials…to heat and flame… [Results] are not intended to be used…to assess the potential xstm hazards of a material c1929 use. Referred to as SIT, the spontaneous or self-ignition temperature is the lowest temperature at which the test piece self-ignites without the existence of an added flame or external source of ignition.
Furniture Testing Machine Need help or have v1929 question? Through our network of over 43, people in 1, laboratories and offices in countries, Intertek provides quality and safety solutions to a wide range of industries around the world. Global Reach Intertek is the industry leader with over 42, people in 1, locations in over countries. Please first log in with a verified email before subscribing to alerts. We have no amendments or corrections for this standard. When plastics ignite and burn, the heat, flames, and gases released can result in catastrophic loss of life and property.
Standards Subsctiption may be the perfect solution. Test values are expected to rank materials according to ignition susceptibility under actual use conditions.
16mm SG ASTM D1929
Equipped with built-in fan to provide air source, and precise control of the flow meter is equipped with imported gas flow. Your Alert Profile lists the documents that will be monitored. Adequate safeguards for personnel and property shall be employed in conducting these tests. Depending on whether or not ignition has occurred, the temperature is lowered or raised, and the test is repeated s1929 a fresh specimen.
Stainless steel container Dimensions: This test specifically benefits companies in the construction, engineering and related materials manufacturing sectors that are required to use plastics that are in full compliance with building regulations, such as the International Building Code — or IBC — as well as more localized ordinances like the Florida Building Code — or FBC — and High Velocity Hurricane Zone — HVHZ.
For cellular plastics with a density of fewer than kilograms per cubic meter, a block of 20 millimeters x 20 millimeters x 50 millimeters should be supplied with any of its outer skin removed. For more information on our fire testing capabilities click here. Application comparison within material through the testing results. No other units of measurement are included in this standard. Vertical Flammability Tester If the document is revised or amended, you will be notified by email.
We have received all the instruments, and will test them, for the moment we have very good feelings.
ASTM D – 16 – Standard Test Method for Determining Ignition Temperature of Plastics
Smoke Density Tester Electrical Test Set Oil Analysis Equipment ICS Number Code With state-of-the-art equipment and ast, highly trained staff, VTEC has been providing cost-effective commercial testing services for well over three decades.
A technician watches for the occurrence of flaming or glowing combustion, flash, explosion, a rapid rise in temperature, or the end of a minute period, whichever comes first.
Auditing Consulting Sourcing Training. Understanding the relative safety of plastic is determined according to the following ASTM D process:. ASTM D — Test Procedures Besides regulations, knowing how a particular plastic responds to heat and flames is simply prudent for builders, suppliers and manufacturers.
Aastm import thermocouple temperature instrument detects the furnace temperature and the sample temperature.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and 1d929 the applicability of regulatory limitations prior to use. I really would like to work with YUYANG, their professional service on the laboratory solution and reliable products help me win much market!
The test lasts for 10 minutes or until ignition occurs.