AUTOOL HTS558 Car Engine Intake Pipe Valve Carbon Deposition Clean Machine 110V

Description

AUTOOL HTS558 Car Engine Intake Pipe Valve Carbon Deposition Clean Machine 110V
Description：
AUTOOL HTS558 Automotive Engine Intake Pipe Valve Clean Machine Valvetronic System Walnut Powder Sand Carbon Deposition Cleaner
What is carbon deposition?
There are some hydrocarbon olefin residues attach on engine intake,cylinder when fuel burn in engine not completely.
These residues change into hard black shell in high temperature condition , that called carbon deposition.
Why need clean carbon deposition?
Carbon deposition will decrease air-fuel ratio, cut down engine output power, increase fuel consumption, engine drastic shake on idle status...
all the thing will hurt engine deeply.
So normally we should clean carbon deposition after every 40000-50000 kilometer trip
What is walnut powder(sand)?
Crash walnut shell into powder, after a vigorous selection process then we get walnut sand.
It show high performance in the three area: hardness, anti-pressure, wear-resisting.
A large amount of  pores on surface of  walnut sand which provide super adsorption capacity, non-toxic and corrosion preventive.
It was hardly dissolved in acid, alkali and water.
Walnut sand is a pure natural polish material, its hardness was lower than metal but higher than carbon deposition, it will clean intake pipe and back side of intake valve thoroughly but no damage
AUTOOL HTS558 walnut powder engine Intake pipe valve clean machine is a advanced equipment for clean engine intake carbon deposition.
Keeping engine in healthy status, make sure engine provide high quality power constantl
y.
Features：
1.
【Deep removal of carbon deposits】Deeply remove the highly sticky carbon deposits on the intake manifold, intake & exhaust valves.
（Solve the problems of unstable idling, insufficient fuel combustion, and reduced air-fuel ratio.)
2.
【External air source】This enables the walnut sand grit to strike the carbon deposits more powerfully and efficiently.
3.
【Built-in dust filter】It can separate the recovered walnut sand grit from carbon deposits for recycling.
4.
【Integrated design】The walnut sand grit can be sprayed and recovered simultaneously.
5.
【3 year warranty】For damage caused by non-human factors, we promise to resend parts for free within 3 years.
Recommend:
1.Air pump pressure should more than 0.7Mpa (7bar/102PSI)
2.Walnut powder diameter should between 0.4-0.8mm, amount in 2-4KG(4-9LB)
3.Cleaning time between 1-3 minutes
Bullet point:
AUTOOL HTS558 is a special machine for engine Intake pipe and intake valve back side clean.
Close intake valve, then spray walnut powder into engine intake via air pump(not include), meanwhile HTS558 will recycle walnut powder by vacuum.
This is a closed loop.
Walnut powder will impact carbon deposition on inner wall of intake pipe.
After thousands of impact,  carbon deposition will be clear thoroughly
Chemical cleaning agent will corrodes pipe and shortens the lifetime of engine.
Walnut powder is pure natural polish material.
It show high performance in  hardness, anti-pressure and wear-resisting.
Walnut powder hardness was lower than metal but higher than carbon deposition.
Take these advatages, AUTOOL HTS558 will clean clean intake pipe and back side of intake valve thoroughly but no damage
High-precision engine system is sensitive to foreign matter of intake pipe, such as BMW valvetronic system.
That is why we need AUTOOL HTS558 to clean  carbon deposition in intake pipe.
Engine should be closed before clean, then turn crankshaft to close intake valve.
AUTOOL HTS558 clean one intake pipe
each time, 6 cylinder engine should cleaned 6 times one by one(and so on)
AUTOOL HTS558 is specail for intake pipe and intake valve back side clean only, if you want to clean carbon deposition on injector/throttle valve/cylinder, please choose AUTOOL CT150,AUTOOL CT200 or AUTOOL C100.
Walnut powder not include in package,please get it in local market;
High pressure air pump is requirement(not include in package);
Walnut powder residual in intake pipe will go to ashes in high temperature after engine start
Getting AUTOOL HTS558 immediately, start your new business
How to use?
1.Open head cover of  AUTOOL HTS558 and pour into walnut powder (need 2-
4KG ), press dust guard on walnut powder then close cover
2.Join spary gun muzzle and recycle hose together (there is a hole on recycle
hose)
3.Remove intake manifold of engine, plug spary gun into intake, turn crankshaft
to close intake valve.
Connect high pressure air pump((not include)) to
HTS558
4.Connect AC power, start clean.
The process should last 1-3
minutes(depending on carbon deposition circumstances)
5.Close AUTOOL HTS558, check up cleaning result.
Normally,  walnut powder
can be reuse 5-10 times(depending on carbon deposition circumstances)
Product
parameters
：
Package includes:
1x AUTOOL HTS558 unit
2x Spray gun
1x Goggles
1x Recycle hose
1x Recycle hose and spray gun connector
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
We only accept PayPal payments.
Payment should be made within 5 days after bidding ends.
We are not responsible for buyers' local taxes.
（1） Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer responsibility.
（2）Please check with your country customs office to determine what these additional costs will be prior to bidding / buying.
Delivery details
We only ship parcel to the address in eBay payment.
（1）0Please make sure payment address in eBay is correct.
（2）Please be known that different shipping service means different shipping charge and shipping time!!!
（3）All packages will be added with a tracking number.
Terms of sales
（1）Item may be returned for refund or replacement within 30 days of the purchase date. Returned merchandise must be unused, in original packaging and include all accessories. Shipping costs are non-refundable.
（2）Defective products may be returned for repair up to 1 year from the purchase date. Repairs will be processed through the manufacturer, we will assist in the repair procedure in any way we can to expedite the process.
（3）Before any return, a Return Merchandise Authorization (RMA
)
must be obtained
by contacting the seller. Any products returned to us without an RMA will be sent back to the buyer at his/her expense. The buyer is responsible for the cost of returning any merchandise.
About us
（1）We are a professional worldwide wholesale company, with own factory located in China. We supply many products on Automobile consumer . Also offer reasonable prices , excellent customer service and a reliable credit standing are our target!
（2）
We are a professional Authorized dealers of AUTOOL，Launch，Autel and Xtool .
（3）Global logistics system：US warehouse, German warehouse, China warehouse.
Contact us
（1）Our normal business hour is
Monday to Friday 9:00 AM to 6:00 PM Beijing TIME.
（2）Please email me through "
MY MESSAGES
" on eBay, if you have any questions about our listings or inventory or troubles.
（3）Welcome your any-time parchase!